Dentonia Announces Stafford Tungsten Project Rock Panel Sampling Results
Wednesday, 02 June 2010 03:54 PM
Dentonia Resources Ltd. (‘Dentonia’ or the ‘Company’) is pleased to announce the results of 3 panel samples taken from the Company’s Stafford Tungsten Project under the supervision of James Turner, P. Geo. The sampling location is a 4m tungsten (‘W’) bearing skarn at kilometre 11 of the Stafford logging road at the head of Loughborough Inlet on the southern BC coast, initially reported by Dentonia on August 25, 2009.
The results are summarized chronologically in the following table:
ROCK PANEL SAMPLE RESULTS
|
Sample |
Date |
Interval (m) |
Weight (kg) |
Area (m2) |
W (%) |
WO3 (%) |
|
A |
Sept. 21, 2009 |
18-19 |
100 |
1 |
1.59 |
2.01 |
|
B |
March 3, 2010 |
18-22 |
900 |
6 |
0.391 +/- 0.04% |
0.49 +/- 0.05% |
|
C |
April 22, 2010 |
17-18 |
16.3
|
0.2 |
8.18 |
10.32 |
Note: WO3 (‘Tungsten tri-oxide’) = 1.2616 x W
These rock sample results demonstrate that tungsten grades in complex skarn geological setting can vary widely, in this case, depending upon sample size, interval length, and surface area.
A - Sampled September 21, 2009
100 kilograms of rock sample material was placed in five pails, flown to Campbell River by helicopter, transported by vehicle to Acme Analytical Laboratories (“Acme”) in Vancouver, BC. The pails were unsealed by Acme, and five random, approximately 1kg, rock samples were taken from each pail and assayed by the X-ray Fluorescence/Fusion method.
. . . 2
Dentonia Resources Ltd.
News Release
June 2, 2010
Page 2
B - Sampled March 3, 2010
Sampling was carried out to more accurately determine the tungsten value of a large (900kg) sample and to produce standards for future assaying. The sampling was reported by the Company on March 11, 2010. The analytical procedures and results from 11 independent laboratories reporting to Canadian Resources Laboratories Ltd. in Langley, BC are given below:
-Method of Preparation: Reject reference material was dried, crushed, pulverized and then passed through a 270 mesh screen. The +270 material was discarded. The -270 material was mixed for 5 days in a rotary mixer. Splits were taken and sent to 11 laboratories for round robin assaying.
-Origin of Reference Material: The reference material was supplied by Dentonia Resources Ltd. from its Stafford Tungsten Project in BC. The main showing consists of a calc-silicate contact metamorphic deposit (tungsten existing as scheelite).
Round-robin Assaying Results
|
Sample |
Lab 1 |
Lab 2 |
Lab 3 |
Lab 4 |
Lab 5 |
Lab 6 |
Lab 7 |
Lab 8 |
Lab 9 |
Lab 10 |
Lab 11 |
|
|
W % |
W % |
W % |
W % |
W % |
W % |
W % |
W % |
W % |
W % |
W % |
|
CDN-W5-1 |
0.404 |
0.38 |
0.530 |
0.423 |
0.353 |
0.376 |
0.39 |
0.390 |
0.375 |
0.401 |
0.404 |
|
CDN-W5-2 |
0.402 |
0.38 |
0.504 |
0.422 |
0.357 |
0.374 |
0.41 |
0.401 |
0.341 |
0.401 |
0.411 |
|
CDN-W5-3 |
0.406 |
0.37 |
0.522 |
0.414 |
0.355 |
0.377 |
0.39 |
0.389 |
0.366 |
0.399 |
0.420 |
|
CDN-W5-4 |
0.384 |
0.38 |
0.535 |
0.417 |
0.357 |
0.366 |
0.40 |
0.401 |
0.352 |
0.393 |
0.410 |
|
CDN-W5-5 |
0.392 |
0.38 |
0.501 |
0.417 |
0.354 |
0.376 |
0.40 |
0.411 |
0.378 |
0.390 |
0.426 |
|
CDN-W5-6 |
0.410 |
0.39 |
0.484 |
0.421 |
0.364 |
0.369 |
0.42 |
0.391 |
0.365 |
0.406 |
0.421 |
|
CDN-W5-7 |
0.380 |
0.38 |
0.547 |
0.419 |
0.357 |
0.377 |
0.37 |
0.387 |
0.379 |
0.398 |
0.396 |
|
CDN-W5-8 |
0.405 |
0.39 |
0.513 |
0.414 |
0.361 |
0.375 |
0.41 |
0.401 |
0.345 |
0.417 |
0.370 |
|
CDN-W5-9 |
0.404 |
0.38 |
0.499 |
0.420 |
0.363 |
0.384 |
0.39 |
0.407 |
0.347 |
0.411 |
0.394 |
|
CDN-W5-10 |
0.399 |
0.38 |
0.532 |
0.419 |
0.365 |
0.391 |
0.42 |
0.409 |
0.310 |
0.409 |
0.403 |
|
Mean |
0.399 |
0.381 |
0.517 |
0.419 |
0.359 |
0.377 |
0.399 |
0.399 |
0.356 |
0.403 |
0.406 |
|
Std. Deviation |
0.0100 |
0.0057 |
0.0197 |
0.0031 |
0.0043 |
0.0070 |
0.0137 |
0.0089 |
0.0214 |
0.0083 |
0.0164 |
|
% RSD |
2.51 |
1.49 |
3.81 |
0.74 |
1.21 |
1.86 |
3.43 |
2.22 |
6.01 |
2.06 |
4.04 |
Note: Results from Lab 3 were excluded for failing the “t test” (statistical value test)
RSD (root standard deviation) is the indication of tightness of results (low is better)
-Assay Procedures: Laboratories were requested to employ their usual ore-grade assay procedure. The following methods were used:
a) phosphoric acid / ICP;
b) neutron activation;
c) MA / ICP;
d) fusion / XRF; and
e) fusion / ICP.
. . . 3
Dentonia Resources Ltd.
News Release
June 2, 2010
Page 3
-Statistical Procedures: The final limits were calculated after first determining if all data was compatible within a spread normally expected for similar analytical methods done by reputable laboratories. Data from any one laboratory was removed from further calculations when the mean of all analysis from that laboratory failed a “t test” of the global means of the other laboratories. The mean and standard deviation were calculated using all remaining data. Any analysis that fell outside of the calculated mean ±2 standard deviations was removed from the ensuing data base. The mean and standard deviations were again calculated using the remaining data. This method is different from that used by government agencies in that the actual “between-laboratory” standard deviation is used in the calculations. This produces upper and lower limits that reflect actual individual analysis rather than a grouped set of analysis. The limits can, therefore, be used to monitor accuracy from individual analysis, unlike the Confidence Limits published on other standards.
-Participating Laboratories (not in same order as listed in table of results): Acme Analytical Laboratories Ltd., Vancouver, BC; Actlabs, Ancaster, Ont.; Assayers Canada Ltd., Vancouver, BC; ALS Chemex Laboratories, North Vancouver, BC; EcoTech Laboratory, Kamloops, BC; Genalysis Laboratory Services Pty. Ltd., Australia; Labtium Laboratory, Finland; International Plasma Labs. Ltd., Vancouver, BC; OMAC Laboratories Ltd., Ireland; TSL Laboratories, Saskatoon, Sask.; Ultra Trace Laboratory, Australia.
C - Sampled April 22, 2010
These rock samples were taken from a 1m higher-grade interval (17-18) previously identified by channel sampling and confirmed with an ultra-violet lamp in darkness. Rock samples were taken from the showing face and placed in three sample bags which were transported directly to ACME Laboratories in Vancouver for analysis by the same X-Ray Fluorescent/Fusion technique that was used on Sample A. The results are summarized below:
Rock Sample Weighted Average WO3 from 1m Interval (17-18)
|
Sample Number |
Weight (kg) |
Assay Value W (%) |
Wt x W (kg-%) |
Weighted Average W (%) |
Weighted Average WO3 (%) |
|
13155 |
5.92 |
10.95 |
64.82 |
|
|
|
13166 |
5.50 |
6.83 |
37.57 |
|
|
|
13157 |
4.87 |
6.33 |
30.83 |
|
|
|
|
16.29 |
|
133.22 |
8.18 |
10.32 |
Note: WO3= 1.2616 x W
The current world price of tungsten has increased by approximately 10% over the past six months to approximately US$29/kg.
. . . 4
Dentonia Resources Ltd.
News Release
June 2, 2010
Page 4
The Stafford Tungsten Project, held under an option agreement to acquire a 100% interest reported in the Company’s news release of January 7, 2010, encompasses a total of 27,775ha and is located approximately 80kms north of Campbell River, on mainland BC. Access is by boat, seaplane or helicopter to Fraser Bay, at the head of Loughborough Inlet. The Claims can be reached either by helicopter or by an 11km-logging road inland from Fraser Bay. A NI 43-101 compliant technical report, prepared by James A. Turner, P.Geo, an independent consultant and QP with respect to the Stafford Tungsten Project, can be found on Sedar at www.sedar.com or the Company’s web site at www.dentonia.net.
Dentonia Resources Ltd. is a Canadian mineral exploration and development company with a portfolio of diverse exploration projects consisting of diamond and tungsten prospects, located respectively, in the Northwest Territories and British Columbia, Canada.
The above information in this news release was prepared under the direction of Mr. Turner, a Qualified Person as defined by National Instrument 43-101, who has read and approves the information contained herein.
For further information, please contact Adolf Petancic, President at (604) 682-1141.
Neither the TSX Venture Exchange nor its Regulation Services Provider (as that term is defined in the policies of the TSX Venture Exchange) accepts responsibility for the adequacy or accuracy of this news release
